UNILOY SW2000-2X615

(1) USED 2,000 TON, 100 LB UNILOY SPRINGFIELD MODEL SW2000-2X615 STRUCTURAL FOAM MACHINESPECIFICATIONS: -2000 TON CLAMP AT 3000 PSI HYDRAULIC -FULLY HYDRAULIC CLAMP -86" X 130" PLATEN (43" X 102" BETWEEN TIE RODS) -OVERALL NOZZLE PATTERN 60"H X 84"W, WITH ADDITIONAL LOCATIONS IN PLATEN EXTENSIONS -STROKE; 72" -DAYLIGHT; 102" MAX - 12" MIN (WITH SPACER) -CLAMP LINEAR POSITION AND PROPORTIONAL VALVE CONTROLS, CLAMP OPEN/CLOSE SPEED -DUAL 6" - 30/1 EXTRUDERS, OPTIMIZED HIGH DENSITY (HDPE) SCREW PROFILE; DUAL 400 HP DRIVE; 4000 LBS/HR TOTAL OUTPUT HDPE -SHOT SIZE; 100 LBS HIPS (TWIN 1540 CUBIC INCH ACCUMULATORS) -32 NOZZLE CONTROLS -TWO SHOT SEQUENTIAL STRUCTURAL WEB SYSTEM WITH ABILITY TO RUN STRUCTURAL FOAM -ELECTRONIC SHOT CONTROL WITH LINEAR TRANSDUCERS -INDEPENDENT TWO STAGE INJECTION; 6000 PSI PER ACCUMULATOR WITH PROPORTIONAL CONTROL VALVES -MACO 8000 MICROPROCESSOR -AUTOMATIC LUBRICATION (TRABON) -MOLD WATER MANIFOLDS ON STATIONARY/MOVING PLATENS -MOLD MOUNTING TO BUYER'S SPECIFICATIONS -CUSTOM MANIFOLDS FOR 2 INFILTRATOR MOLDS, INCLUDING CUSTOM NOZZLE PATTERN -REMOVE FRONT AND REAR COOLING ON EXTRUDER -REPLACE ALUMINUM CAST-IN HEATER BANDS WITH STANDARD BANDS ON EXTRUDERS -CHANGE WATER MANIFOLDS FROM ROUND TO RECTANGULAR AND RELOCATE ON PLATENS PER SF1500 #2 -INJECTION PRESSURE INDICATOR ON MACO -MACO CONTROL SCREEN CONFIGURATION ACCESSIBILITY (CHANGE SEQUENCE) -MACO DISPLAY ON REAR OF MACHINE (REMOTE) -CONFIGURE NOZZLE MANIFOLDS TO PERMIT STANDARD HOSE LENGTHS -ADD MACO FUNCTION TO ALLOW SETTING GAS PACK TIMES SEPARATE FOR FRONT AND REAR ACCUMULATORS -USE HIGH TEMPERATURE INSULATION WIRES IN JUNCTION BOXES OF NOZZLES -2 - 1' PLATEN EXTENSIONS, GUSSET REINFORCED, WITH 2 ADDITIONAL NOZZLE LOCATIONS PER LAYOUT -XALOY 8000 MELT ACCUMULATORS AND PLUNGERS -LARGE FEED THROAT MAGNETS -REAR SIDE MACO MONITOR -ALL ADDITIONAL CHANGES INCORPORATED IN SF1500 #2 -CUSTOM MANIFOLDS FOR TWO INFILTRATOR MOLDS -1500 TONS OF CLAMP @ 2200 PSI -ADEQUATE TRAVERSE FOR 2 MOLDS (@20,000 POUNDS EACH ON MOVING PLATEN). AT NORMAL SPEED TRAVERSING SPEEDS -3200 POUNDS PER HOUR SCREW OUTPUT CONTINUOUS W/HDPE -APPROPRIATE SIZED WATER MANIFOLDS FOR COOLING 60 POUNDS HDPE ON 45 SECOND COOL CYCLE -OIL TEMPERATURE COOLERS TO MAINTAIN OIL AT NORMAL LEVEL @2200 PSI AND 1 MINUTE 15 SECOND CYCLE -DUMP VALVE WILL NOT OPEN UP DUE TO SCREW HEAD PRESSURE OR INJECTION PRESSURE BELOW 6,000 PSI -ALL SYSTEMS TO PERFORM @ 100% CAPACITY AT 100 DEG FAHRENHEIT AMBIENT TEMPERATURE -VIBRATION AND SHOCK SYSTEMS IN PLACE TO PREVENT MACHINE DAMAGE -RAMP TIME OF DC DRIVE TO BE EQUAL OR BETTER THAN 300 HP DC DRIVE MODELS -EXTRUDER AND TWO ACCUMULATORS TO ALLOW FOR INSTALLATION OF THERMAL BLANKETS