LEITZ PMM 544

(1) Used Leitz PMM 544 Coordinate Measuring Machine Mechanically Refurbished, Electronically Updated 1 Year WarrantySPECIFICATIONS: Type: Fixed Bridge Weight: 8000 lbs. Measuring Volume: X Axis: 500mm (19.7") Y Axis: 400mm (15.75") Z Axis: 400mm (15.75") Volumetric Accuracy: 1.6um+L/300 Linear Accuracy per Axis (Center of Volume): 1.2um+L/400 System Resolution (Combined - Scales and Probe Head): 0.5um (20u") Measuring Repeatability (In Zero Force point mode): 1.0um (40u")General: Granite structure with Lab Grade metrology surfaces. Axes powered by high speed DC servo motors which can position at a velocity of approximately 50mm/sec. (2"/sec.). All three axis are equipped with linear scales which have uncompensated accuracy's of +/- 0.5um over their full length. As standard equipment, the SCEPTRETM System allows the performance of inspection tasks beyond those of the most advanced measuring systems in the world.includes the following items and features (NEED TO VERIFY): The SCEPTRETM Probe-1 Head (Contact) SCEPTRETM Computer / Controller Four Axis Joystick Basic SCEPTRETM Software - Control, Collection and Evaluation High Resolution 14" Color Monitor Keyboard Color Printer PC / Controller Floor Cabinet 500x400x400mm 19.5x15.5x15.5" Measuring Volume Full One (1) Year Warranty - (Parts and Material) Perpetual On-Going Software Updates and SupportAlso includes: Installation / Calibration (Parts & Labor) Trainning and Application Assistance: 4day'sOPTIONAL EQUIPMENT: The Machine listed above is a complete system. The Optional Equipment listed here is meant to enhance the performance of the CMM. STC-410 Magnetic Probe-2 (in place of the Probe-1): $4,000.00 The Magnetic Probe-2 allows the user to interchange and increment various Probehead Adapters containing user styli setups. These Adaptors have 17 styli receiving locations utilizing normal styli tips with M4 threads. The Probehead adapters can be indexed about the Z Axis in 5° increments. The price of this probe, if purchased alone is $20,000.00. MPC-465 Magnetic Probe Changer: $8,001.00 Stylus Changer Frame Set of 3 Storage Docks 2 Extra Probehead Adapters Stylus Changer software This package allows for the automatic changing of various Probehead adapters. PSO-650 Pallet System Option: $7,482.00 Table mounted Framework Set of 3 Pallets Pallet SoftwareThe Pallet System Option is an exceptional enhancement to any upgraded system. The pallets are used primarily for production run of component measurement. Each pallet will hold a specific component and that particular pallet, when placed inside the framework, will automatically call up and run that specific program for that specific component. OTHER AVAILABLE OPTIONS Hardware (inclusive of software support): BOP-160 Temperature Sensors, Interface & Compensation: 6,800.00 VIS-300 Sceptre Vision System w/all necessary hardware and software: 27,705.00 VOP-310 6" x 6" Light Table: 2,450.00 EQS-630 12.7MM Calibration Ball with Stand: 625.00 EQS-640 Styli Kit - Standard M4 Thread / 18 pieces: 808.00 ROT-600 18" Rotary Table Option w/all necessary hardware and software: 65,851.00SCEPTRETM System SpecificationsSCEPTRETM "Contact" Probe (SCP) Probe can withstand normal handling without damage Repeatability: Typically 0.2um or less dependent on machine and conditions Measuring Range +/- 3mm in X, Y, Z with collision protection Number of probe pin mounting locations - 17 (M4 thread) Force / Displacement ratio - 15 grams per 25um (0.001") displacement Probing Force Range - 10 grams to 200 grams, software selectable Internal support system - flex wire parallelogram linkages, all axis Position sensors - infrared optical transmitters/ receivers, all axis Internal response rate - one megahertz Probe Head analog signals pre-amplified inside probe head SCEPTRETM Computer/Controller: Single Industrial PC Unit containing: Single Board 2.4 GHz CPU Windows Operating system 200 GB Hard Drive 256 Meg Memory A/D Converter and Interconnect Board DMC-1030 Motion Controller SVGA-PCI N Bus Controller All necessary cables, wiring, connectors, etc.NOTE: The power consumption when controlling the CMM is 4.75 amp @ 110va. Air pressure requirements are 80 psi (filtered, dried, and free from oil and water), 3-4 cfm consumption minimum. SCEPTRETM Software: The following is a partial list of software features that imparts the character of the system, but is not exhaustive. The 200 page Language Reference Manual is required to give a complete overview of the system software. Periodic software updates will continue to be added to the main software package. All such updates, as a matter of EMD, Inc. policy, will be made available at no additional charge so long as the original User owns the system. Special software routines which may be developed for various purposes, and which do not necessarily have broad usage, are not included in this category. Up to 300 fully compensated data points per second Up to 32,700 data points per element, or per individual file Full graphic output of over 200 icon-selectable features Can control up to six axis, rotary or linear System may be used with or without password protection On-screen graphic display of many machine functions, such as: Validity of calibration data Real-time display of actual scan force vector Position of part "zero" inside measuring volume of machine Orientation of part reference system relative to machine axes Automatic system status screen, with icons Program listings and on-screen help files Allows for the creation of up to 1000 macros, easily recalled Up to 1000 probe tip calibrations may be stored in memory Data upload / download through RS 232 port Equivalent command string automatically displayed on screen as part programs are created with icons, allowing easy switching out of menu mode into command mode Complete modeling of SCEPTRETM probe to machine (alignment and resolution) Full compensation for probe pin and deflections in 3D space Self teach, full documentation and periodic updates of main program Temperature, straightness, squareness, scale linearity compensation Vector positioning between measurement points Obtaining individual data points without probe pin calibration, with full deflection compensation Graphic display of standard deviation population distribution Graphic display of sequential point deviation histogram Scanning in machine or part coordinates Automatic scanning in a plane defined by a previous measurement Two or three axis self-centering in machine or part coordinates, to find a low point Two or three axis self-centering in machine or part coordinates, to find a high point Scanning while self-centering in a groove or on a ridge (low or high point) Digitizing unknown shapes using same approach as for standard elements Averaging a stream of data while staying in static contact with workpiece (eliminates vibration effects) Rapid method of taking individual data points (Quick Measure) Individual point probing at a specific force, or over a range of forces Individual point probing without exceeding a predetermined maximum force Full software control of scan spee