Chat with us, powered by LiveChat
UNILOY SW2000-2X615
Image coming soon!

2000 TON 100 LB

Brand

UNILOY

Model

SW2000-2X615

Year

None

Stock #

27300

Condition

Used

Request a Quote

Specs & More…

Specifications

(1) USED 2,000 TON, 100 LB UNILOY SPRINGFIELD MODEL SW2000-2X615 STRUCTURAL FOAM MACHINE

SPECIFICATIONS:
-2000 TON CLAMP AT 3000 PSI HYDRAULIC
-FULLY HYDRAULIC CLAMP
-86" X 130" PLATEN (43" X 102" BETWEEN TIE RODS)
-OVERALL NOZZLE PATTERN 60"H X 84"W, WITH ADDITIONAL LOCATIONS
IN PLATEN EXTENSIONS
-STROKE; 72"
-DAYLIGHT; 102" MAX - 12" MIN (WITH SPACER)
-CLAMP LINEAR POSITION AND PROPORTIONAL VALVE CONTROLS, CLAMP
OPEN/CLOSE SPEED
-DUAL 6" - 30/1 EXTRUDERS, OPTIMIZED HIGH DENSITY (HDPE) SCREW
PROFILE; DUAL 400 HP DRIVE; 4000 LBS/HR TOTAL OUTPUT HDPE
-SHOT SIZE; 100 LBS HIPS (TWIN 1540 CUBIC INCH ACCUMULATORS)
-32 NOZZLE CONTROLS
-TWO SHOT SEQUENTIAL STRUCTURAL WEB SYSTEM WITH ABILITY TO RUN
STRUCTURAL FOAM
-ELECTRONIC SHOT CONTROL WITH LINEAR TRANSDUCERS
-INDEPENDENT TWO STAGE INJECTION; 6000 PSI PER ACCUMULATOR WITH
PROPORTIONAL CONTROL VALVES
-MACO 8000 MICROPROCESSOR
-AUTOMATIC LUBRICATION (TRABON)
-MOLD WATER MANIFOLDS ON STATIONARY/MOVING PLATENS
-MOLD MOUNTING TO BUYER'S SPECIFICATIONS
-CUSTOM MANIFOLDS FOR 2 INFILTRATOR MOLDS, INCLUDING CUSTOM
NOZZLE PATTERN
-REMOVE FRONT AND REAR COOLING ON EXTRUDER
-REPLACE ALUMINUM CAST-IN HEATER BANDS WITH STANDARD BANDS ON
EXTRUDERS
-CHANGE WATER MANIFOLDS FROM ROUND TO RECTANGULAR AND RELOCATE
ON PLATENS PER SF1500 #2
-INJECTION PRESSURE INDICATOR ON MACO
-MACO CONTROL SCREEN CONFIGURATION ACCESSIBILITY (CHANGE
SEQUENCE)
-MACO DISPLAY ON REAR OF MACHINE (REMOTE)
-CONFIGURE NOZZLE MANIFOLDS TO PERMIT STANDARD HOSE LENGTHS
-ADD MACO FUNCTION TO ALLOW SETTING GAS PACK TIMES SEPARATE FOR
FRONT AND REAR ACCUMULATORS
-USE HIGH TEMPERATURE INSULATION WIRES IN JUNCTION BOXES OF
NOZZLES
-2 - 1' PLATEN EXTENSIONS, GUSSET REINFORCED, WITH 2 ADDITIONAL
NOZZLE LOCATIONS PER LAYOUT
-XALOY 8000 MELT ACCUMULATORS AND PLUNGERS
-LARGE FEED THROAT MAGNETS
-REAR SIDE MACO MONITOR
-ALL ADDITIONAL CHANGES INCORPORATED IN SF1500 #2
-CUSTOM MANIFOLDS FOR TWO INFILTRATOR MOLDS
-1500 TONS OF CLAMP @ 2200 PSI
-ADEQUATE TRAVERSE FOR 2 MOLDS (@20,000 POUNDS EACH ON MOVING
PLATEN). AT NORMAL SPEED TRAVERSING SPEEDS
-3200 POUNDS PER HOUR SCREW OUTPUT CONTINUOUS W/HDPE
-APPROPRIATE SIZED WATER MANIFOLDS FOR COOLING 60 POUNDS HDPE
ON 45 SECOND COOL CYCLE
-OIL TEMPERATURE COOLERS TO MAINTAIN OIL AT NORMAL LEVEL @2200
PSI AND 1 MINUTE 15 SECOND CYCLE
-DUMP VALVE WILL NOT OPEN UP DUE TO SCREW HEAD PRESSURE OR
INJECTION PRESSURE BELOW 6,000 PSI
-ALL SYSTEMS TO PERFORM @ 100% CAPACITY AT 100 DEG FAHRENHEIT
AMBIENT TEMPERATURE
-VIBRATION AND SHOCK SYSTEMS IN PLACE TO PREVENT MACHINE DAMAGE
-RAMP TIME OF DC DRIVE TO BE EQUAL OR BETTER THAN 300 HP DC
DRIVE MODELS
-EXTRUDER AND TWO ACCUMULATORS TO ALLOW FOR INSTALLATION OF
THERMAL BLANKETS

Proud member of the MDNA
Contact